1. Introduction

1.2. Trademarks

All trademarks are the property of their respective holders.

1.3. Disclaimer

No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this document. The information provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of this document. The information and product specifications within this document are subject to change at any time, without notice and without obligation to notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior notice.

1.4. Regulatory Compliance

FCC-A Radio Frequency Interference Statement:

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his personal expense.

Note

The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

Note

The product described in this document is designed for general use, VIA Technologies assumes no responsibility for the conflicts or damages arising from incompatibility of the product. Check compatibility issue with your local sales representatives before placing an order.

1.5. Battery Recycling and Disposal

  • Only use the appropriate battery specified for this product.
  • Do not re-use, recharge, or reheat an old battery.
  • Do not attempt to force open the battery.
  • Do not discard used batteries with regular trash.
  • Discard used batteries according to local regulations.

1.6. Safety Precautions

  • Always read the safety instructions carefully.
  • Keep this User’s Manual for future reference.
  • All cautions and warnings on the equipment should be noted.
  • Keep this equipment away from humidity.
  • Lay this equipment on a reliable flat surface before setting it up.
  • Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet.
  • Place the power cord in such a way that people cannot step on it.
  • Always unplug the power cord before inserting any add-on card or module.
  • If any of the following situations arises, get the equipment checked by authorized service personnel:
    • The power cord or plug is damaged.
    • Liquid has penetrated into the equipment.
    • The equipment has been exposed to moisture.
    • The equipment has not worked well or you cannot get it work according to User’s Manual.
    • The equipment has dropped and damaged.
    • The equipment has obvious sign of breakage.
  • Do not leave this equipment in an environment unconditioned or in a storage temperature above 60°C (140°F). The equipment may be damaged.
  • Do not leave this equipment in direct sunlight.
  • Never pour any liquid into the opening. Liquid can cause damage or electrical shock.
  • Do not place anything over the power cord.
  • Do not cover the ventilation holes. The openings on the enclosure protect the equipment from overheating

1.7. Box Contents and Ordering Information

  • 1 × VAB-600 embedded board (with WM8950 Cortex-A9 processor)
  • 1 × DC-In cable
  • 1 × Front Panel cable
  • 1 × Front Audio cable
  • 1 × COM connector cable
  • 1 × USB cable (for the optional WLAN USB module)

The VAB-600 basic kit and wifi kit can be ordered on the VIA Springboard website.